About

 

 

What are your opinions with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is additionally a moderately hard job. If the old bathtub is easily easily accessible, the task can move speedily; if you need to open a wall to remove the old bathtub and place the brand-new tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub and also set in the brand-new one. Make sure you have certified yourself for the work and fit trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly help you set up a brand-new bath tub in your restroom if you have actually currently bought a new bathtub and also don't need to transform the setup of your previous supply of water pipelines.
Your devices and material list need to comprise the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Preparing for the Installation

First of all, the supporting framework provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last setting.

 

 

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome due to the limited gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

 

 

Installing the Tub

Making use of the two wood boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest flexible tap port to the ideal supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water system and check all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub and also inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its last placement.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the area where the bath satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to permit the activity experienced when the tub remains in use. The sealer can split rather early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant glue as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Do you like reading up on Installing A Bathtub? Leave a remark down the page. We'd be interested to see your opinion about this post. We are looking forward that you visit us again later on. Enjoyed reading our write-up? Please share it. Help somebody else discover it. Thank you so much for your time invested reading it.

Website